Omron D4N-4120 Roller Lever Safety Limit Switch

Remote Pro
SKU: RP000523
IN STOCK

Price:
Sale price$50.00

Omron D4N-4120 Roller Lever Safety Limit Switch – 1NC + 1NO, M20, IP67

The Omron D4N-4120 is a compact, mechanically operated safety limit switch designed to detect the position or end of travel of moving equipment. When a cam or moving component pushes the roller lever, the switch changes its contact state, providing a signal to a compatible control system.

Featuring a resin roller lever, snap-action switching and separate normally closed (NC) and normally open (NO) contacts, it is suitable for position monitoring and travel-limit applications where its specifications match the equipment requirements. The NC contact incorporates a certified direct-opening mechanism for use within an appropriately designed safety circuit.

Features and Specifications

Brand Omron
Model D4N-4120
Switching action Snap-action
Contact configuration 1 normally closed + 1 normally open
Actuator Resin lever with resin roller
Roller size 17.5mm diameter × 6.8mm wide
Lever radius 26mm
Cable entry Single M20 entry
Enclosure protection IP67
Electrical protection Class II double insulation
Operating temperature −30°C to +70°C, without icing
Mechanical durability Minimum 15 million operations
Maximum operating frequency 30 operations per minute
Country of manufacture Japan, as marked on the pictured unit

Electrical Ratings

  • AC-15: 3A at 240V AC.
  • DC-13: 0.27A at 250V DC.

These ratings describe the switch’s contact switching capacity, rather than a required power supply. The switch operates mechanically and does not generate voltage.

Terminal Identification and Operation

Terminals Contact Type Lever Released Lever Actuated Past Switching Point
11–12 Normally closed (NC) Closed / continuity Open / no continuity
33–34 Normally open (NO) Open / no continuity Closed / continuity

The contact pairs are electrically separate and do not share a common terminal. Only the 11–12 NC contact has the certified direct-opening function. Always identify connections using the terminal markings inside the switch.

Wiring and Installation Instructions

Installation must be completed by a suitably qualified installer, with mains wiring handled by a licensed electrician. Follow the Omron instructions supplied with the switch and the equipment manufacturer’s wiring diagram.

  1. Isolate the equipment. Disconnect all relevant power supplies, verify the circuit is de-energised and secure moving equipment before opening the switch.
  2. Check the controller requirements. Confirm whether the controller requires a normally closed or normally open contact, and identify its designated input terminals.
  3. Connect the appropriate contact pair. For a controller requiring a normally closed, voltage-free limit input, connect its designated input and input-common terminals across 11–12. For a normally open, voltage-free position input, use 33–34. These examples apply only to controllers that specify dry-contact inputs. Do not apply an external voltage to a controller input unless its manufacturer explicitly requires it.
  4. Fit the cable entry. Use a suitable non-metallic M20 cable gland matched to the cable diameter and required sealing performance. Do not use metal connectors or metal conduits.
  5. Terminate the conductors. The supplied instructions specify 0.5–0.75mm² (AWG20–18) wire with suitable insulated M3.5 crimp terminals. Keep wiring clear of the moving mechanism and cover seal.
  6. Tighten and close. Tighten terminal screws to 0.6–0.8N·m and the cover screw to 0.5–0.7N·m. Ensure the cover seal is correctly seated and no wires are trapped.

Testing and Commissioning

With power isolated and the switch disconnected from the controller, check continuity across each contact pair using a multimeter. Operate and release the lever several times and confirm the results match the terminal table.

After reconnecting the wiring and closing the enclosure, test the equipment under controlled conditions to verify the intended limit response. Safety applications require validation of the complete safety circuit; an audible click alone does not confirm direct opening.

Application and Compatibility Notes

The supplied instructions specify indoor use, despite the IP67 enclosure rating. Correct cable sealing and cover installation are required to maintain enclosure protection.

Before ordering, compare the model number, mounting arrangement, actuator travel, contact configuration and electrical ratings with your existing equipment. Final controller connections must follow the equipment manufacturer’s wiring diagram.

Remote Pro

WARNING! This product may contain a button/coin cell battery. To prevent possible SERIOUS INJURY or DEATH:

  • Keep new and used batteries out of reach of children at all times.
  • Do not use the product if the battery compartment is damaged or doesn’t close securely.
  • Dispose of used batteries immediately and safely - even flat batteries can cause harm.
  • Do not ingest the battery. Chemical burn hazard.
  • Act fast if you suspect a battery has been swallowed or inserted - severe or fatal injuries can occur within 2 hours.
  • Seek immediate medical attention or call:
    – Australia: Poisons Information Centre on 13 11 26
    – New Zealand: National Poisons Centre on 0800 764 766

Remote Pro supplies aftermarket products designed to be compatible with and to suit a wide range of original brands. Unless a product is expressly stated to be genuine, all items sold on this website are not manufactured, authorised, endorsed, or approved by the original equipment manufacturers (OEMs).

References to brand names, trademarks, or model numbers are used solely to indicate compatibility or suitability for use with the respective equipment. Remote Pro is not affiliated with, sponsored by, or associated with any of these brand owners, and no OEM approval or endorsement is implied.

All trademarks, brand names, and product names remain the property of their respective owners. Remote Pro distributes a range of aftermarket products, including but not limited to remote controls compatible with garage and gate motors and receivers produced by other manufacturers, as well as substitute automotive keys, remote controls, and casings designed to be compatible with vehicles made by other manufacturers.

You may also like